using in-board ez430 FET emulator

Previous Topic Next Topic
 
classic Classic list List threaded Threaded
9 messages Options
Reply | Threaded
Open this post in threaded view
|

using in-board ez430 FET emulator

ravim
Hello every one,

I have a MSP-EXP430F5529 board, which has an in-board ez430-FET emulator board. I have been using MSP-FET430UIF to program it. I want to know if we can use this in-board emulator to program this device.
This is what datasheet says about ez430-FET board :

According to Datasheet:

The area of the PCB labeled as "eZ430-FET Emulator" and bordered by a thick
broken line on the PCB silk screen is an integrated TI Flash Emulation Tool (FET) which is connected to the Experimenter Board by the jumpers on JP16. 
This module is similar to any eZ430 emulator, and provides real-time in-system Spy-Bi-Wire programming and debugging via a USB connection to a PC.
Using the eZ430-FET Emulator module eliminates the need for using an external MSP430 Flash Emulation Tool (MSP-FET430UIF)

when I tried this,  on Ubuntu and on Mac both, this connection is recognized as ez430-rf2500, the mspdebug --usb-list command gives:

Devices on bus 004:
    004:001 1d6b:0003  [serial: 0000:00:14.0]
Devices on bus 003:
    003:015 0451:f432 eZ430-RF2500 [serial: 54FF467625974B3C]
    003:001 1d6b:0002  [serial: 0000:00:14.0]
Devices on bus 002:
    002:002 8087:0024
    002:001 1d6b:0002  [serial: 0000:00:1d.0]
Devices on bus 001:
    001:002 8087:0024
    001:001 1d6b:0002  [serial: 0000:00:1a.0]

so when I tried to install the code (which is working successfully with MSP-FET430UIF) using this connection (tried both tty and raw usb access) I get:

Trying to open interface 1 on 015
Initializing FET...
FET protocol version is 30132072
Configured for Spy-Bi-Wire
Set Vcc: 3000 mV
fet: FET returned error code 4 (Could not find device (or device not supported))
fet: command C_IDENT1 failed
fet: identify failed

and the code does not install, which is obvious since the chip on it is msp430f5529 which is not recognized by  ez430-rf2500 emulator.


I wanted to know if it is possible to use this on board emulator with mspdebug instead of buying a new external MSP-FET430UIF? If it is how to access it.

I would really appreciate any response. Let me know if I am making wrong assumptions or doing it totally wrong?

Thanks and regards,
Ravi
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

Jose Luis Honorato L.
Hi Ravim,

I can't see the output messages you intended to include, but here's a short
how-to. I just hope you don't have a specific problem with your setup.

You can use the ez430-FET emulator to program the msp-exp430f5529 without
any external hardware. Just plug your mini USB cable to the lower left USB
connector (the one in the ez430-FET emulator) and run:

sudo mspdebug rf2500 "prog bin.elf"

That should program the device after a few console messages.

You can use mspdebug with gdb too, for that you should:

   1. Run mspdebug (sudo mspdebug rf2500)
   2. In mspdebug, type gdb
   3. In another window, run msp430-gdb
   4. In gdb, type target remote localhost:2000
   5. Done

This is assuming you have all these tools installed, if not there are
plenty of guides out there on how to install them.

Kind regards,
Jose

On Thu, Jun 20, 2013 at 12:28 PM, ravim <[hidden email]> wrote:

> Hello every one,
>
> I have a MSP-EXP430F5529 board, which has an in-board ez430-FET emulator
> board. I have been using MSP-FET430UIF to program it. I want to know if we
> can use this in-board emulator to program this device.
> This is what datasheet says about ez430-FET board :
>
> According to Datasheet:
>
>
>
> when I tried this,  on Ubuntu and on Mac both, this connection is
> recognized
> as ez430-rf2500, the mspdebug --usb-list command gives:
>
>
>
> so when I tried to install the code (which is working successfully with
> MSP-FET430UIF) using this connection (tried both tty and raw usb access) I
> get:
>
>
>
> and the code does not install, which is obvious since the chip on it is
> msp430f5529 which is not recognized by  ez430-rf2500 emulator.
>
>
> I wanted to know if it is possible to use this on board emulator with
> mspdebug instead of buying a new external MSP-FET430UIF? If it is how to
> access it.
>
> I would really appreciate any response. Let me know if I am making wrong
> assumptions or doing it totally wrong?
>
> Thanks and regards,
> Ravi
>
>
>
> --
> View this message in context:
> http://msp430-gcc-users.1086195.n5.nabble.com/using-in-board-ez430-FET-emulator-tp6740.html
> Sent from the MSP430 gcc - Users mailing list archive at Nabble.com.
>
>
> ------------------------------------------------------------------------------
> This SF.net email is sponsored by Windows:
>
> Build for Windows Store.
>
> http://p.sf.net/sfu/windows-dev2dev
> _______________________________________________
> Mspgcc-users mailing list
> [hidden email]
> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

ravim
In reply to this post by ravim
Thank you Jose,

It works, I got it, I was giving the wrong device it seems. without mentioning the device, it works just fine. Thank you very much. Really appreciate your response.
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

John Willauer
In reply to this post by Jose Luis Honorato L.
How do I eliminate the "Segmentation fault" I get when I try it using:

    Ubuntu          12.04
    mspdebug     0.18-1
    gdb-msp430  7.2~mspgcc-7.2.2
    gcc-msp439  4.5.3~mspgcc-201

--
John
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -


On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:

> Hi Ravim,
>
> I can't see the output messages you intended to include, but here's a short
> how-to. I just hope you don't have a specific problem with your setup.
>
> You can use the ez430-FET emulator to program the msp-exp430f5529 without
> any external hardware. Just plug your mini USB cable to the lower left USB
> connector (the one in the ez430-FET emulator) and run:
>
> sudo mspdebug rf2500 "prog bin.elf"
>
> That should program the device after a few console messages.
>
> You can use mspdebug with gdb too, for that you should:
>
>     1. Run mspdebug (sudo mspdebug rf2500)
>     2. In mspdebug, type gdb
>     3. In another window, run msp430-gdb
>     4. In gdb, type target remote localhost:2000
>     5. Done
>
> This is assuming you have all these tools installed, if not there are
> plenty of guides out there on how to install them.
>
> Kind regards,
> Jose
> _______________________________________________
> Mspgcc-users mailing list
> [hidden email]
> https://lists.sourceforge.net/lists/listinfo/mspgcc-users


------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

Eric Decker
Just asking how to get rid of a "seg fault" isn't to helpful.

What program was actually running?   What version?  What address?


On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[hidden email]> wrote:

> How do I eliminate the "Segmentation fault" I get when I try it using:
>
>    Ubuntu          12.04
>    mspdebug     0.18-1
>    gdb-msp430  7.2~mspgcc-7.2.2
>    gcc-msp439  4.5.3~mspgcc-201
>
> --
> John
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
>
>
> On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:
>
>> Hi Ravim,
>>
>> I can't see the output messages you intended to include, but here's a
>> short
>> how-to. I just hope you don't have a specific problem with your setup.
>>
>> You can use the ez430-FET emulator to program the msp-exp430f5529 without
>> any external hardware. Just plug your mini USB cable to the lower left USB
>> connector (the one in the ez430-FET emulator) and run:
>>
>> sudo mspdebug rf2500 "prog bin.elf"
>>
>> That should program the device after a few console messages.
>>
>> You can use mspdebug with gdb too, for that you should:
>>
>>     1. Run mspdebug (sudo mspdebug rf2500)
>>     2. In mspdebug, type gdb
>>     3. In another window, run msp430-gdb
>>     4. In gdb, type target remote localhost:2000
>>     5. Done
>>
>> This is assuming you have all these tools installed, if not there are
>> plenty of guides out there on how to install them.
>>
>> Kind regards,
>> Jose
>> ______________________________**_________________
>> Mspgcc-users mailing list
>> Mspgcc-users@lists.**sourceforge.net <[hidden email]>
>> https://lists.sourceforge.net/**lists/listinfo/mspgcc-users<https://lists.sourceforge.net/lists/listinfo/mspgcc-users>
>>
>
>
>
>
> ------------------------------------------------------------------------------
> This SF.net email is sponsored by Windows:
>
> Build for Windows Store.
>
> http://p.sf.net/sfu/windows-dev2dev
> _______________________________________________
> Mspgcc-users mailing list
> [hidden email]
> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>
>

--
Eric B. Decker
Senior (over 50 :-) Researcher

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

John Willauer
How do I eliminate the "Segmentation fault" that occurs when I start  
msp430-gdb  using the following procedure Jose Luis Honorato described
in his response to Ravim.

When the msp430-gdb is started, in the second shell, a Segmentation
fault is reported then the msp430-gdb terminates.

I am trying to use  gdb  to debug code running on a Launchpad with a
msp430g2553 chip.

--
John
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -


On 06/22/2013 01:06 PM, Eric Decker wrote:

>
> Just asking how to get rid of a "seg fault" isn't to helpful.
>
> What program was actually running?   What version?  What address?
>
>
> On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[hidden email]
> <mailto:[hidden email]>> wrote:
>
>     How do I eliminate the "Segmentation fault" I get when I try it using:
>
>        Ubuntu          12.04
>        mspdebug     0.18-1
>        gdb-msp430  7.2~mspgcc-7.2.2
>        gcc-msp439  4.5.3~mspgcc-201
>
>     --
>     John
>     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
>
>
>     On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:
>
>         Hi Ravim,
>
>         I can't see the output messages you intended to include, but
>         here's a short
>         how-to. I just hope you don't have a specific problem with
>         your setup.
>
>         You can use the ez430-FET emulator to program the
>         msp-exp430f5529 without
>         any external hardware. Just plug your mini USB cable to the
>         lower left USB
>         connector (the one in the ez430-FET emulator) and run:
>
>         sudo mspdebug rf2500 "prog bin.elf"
>
>         That should program the device after a few console messages.
>
>         You can use mspdebug with gdb too, for that you should:
>
>             1. Run mspdebug (sudo mspdebug rf2500)
>             2. In mspdebug, type gdb
>             3. In another window, run msp430-gdb
>             4. In gdb, type target remote localhost:2000
>             5. Done
>
>         This is assuming you have all these tools installed, if not
>         there are
>         plenty of guides out there on how to install them.
>
>         Kind regards,
>         Jose
>         _______________________________________________
>         Mspgcc-users mailing list
>         [hidden email]
>         <mailto:[hidden email]>
>         https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>
>
>
>
>     ------------------------------------------------------------------------------
>     This SF.net email is sponsored by Windows:
>
>     Build for Windows Store.
>
>     http://p.sf.net/sfu/windows-dev2dev
>     _______________________________________________
>     Mspgcc-users mailing list
>     [hidden email]
>     <mailto:[hidden email]>
>     https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>
>
>
>
> --
> Eric B. Decker
> Senior (over 50 :-) Researcher
>

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

Eric Decker
What version of msp430-gdb are you running?   Where did you get it?

do..

dpkg -l "*msp430*"

and how do you have apt configured?    What repository are you using to get
the tools from?



On Sat, Jun 22, 2013 at 5:10 PM, John Willauer <[hidden email]> wrote:

>  How do I eliminate the "Segmentation fault" that occurs when I start
> msp430-gdb  using the following procedure Jose Luis Honorato described in
> his response to Ravim.
>
> When the msp430-gdb is started, in the second shell, a Segmentation fault
> is reported then the msp430-gdb terminates.
>
> I am trying to use  gdb  to debug code running on a Launchpad with a
> msp430g2553 chip.
>
>
> --
> John
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
>
> On 06/22/2013 01:06 PM, Eric Decker wrote:
>
>
>  Just asking how to get rid of a "seg fault" isn't to helpful.
>
>  What program was actually running?   What version?  What address?
>
>
> On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[hidden email]>wrote:
>
>> How do I eliminate the "Segmentation fault" I get when I try it using:
>>
>>    Ubuntu          12.04
>>    mspdebug     0.18-1
>>    gdb-msp430  7.2~mspgcc-7.2.2
>>    gcc-msp439  4.5.3~mspgcc-201
>>
>> --
>> John
>> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>>
>>
>>
>> On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:
>>
>>>  Hi Ravim,
>>>
>>> I can't see the output messages you intended to include, but here's a
>>> short
>>> how-to. I just hope you don't have a specific problem with your setup.
>>>
>>> You can use the ez430-FET emulator to program the msp-exp430f5529 without
>>> any external hardware. Just plug your mini USB cable to the lower left
>>> USB
>>> connector (the one in the ez430-FET emulator) and run:
>>>
>>> sudo mspdebug rf2500 "prog bin.elf"
>>>
>>> That should program the device after a few console messages.
>>>
>>> You can use mspdebug with gdb too, for that you should:
>>>
>>>     1. Run mspdebug (sudo mspdebug rf2500)
>>>     2. In mspdebug, type gdb
>>>     3. In another window, run msp430-gdb
>>>     4. In gdb, type target remote localhost:2000
>>>     5. Done
>>>
>>> This is assuming you have all these tools installed, if not there are
>>> plenty of guides out there on how to install them.
>>>
>>> Kind regards,
>>> Jose
>>>  _______________________________________________
>>> Mspgcc-users mailing list
>>> [hidden email]
>>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>>
>>
>>
>>
>>
>> ------------------------------------------------------------------------------
>> This SF.net email is sponsored by Windows:
>>
>> Build for Windows Store.
>>
>> http://p.sf.net/sfu/windows-dev2dev
>> _______________________________________________
>> Mspgcc-users mailing list
>> [hidden email]
>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>
>>
>
>
>  --
> Eric B. Decker
> Senior (over 50 :-) Researcher
>
>
>

--
Eric B. Decker
Senior (over 50 :-) Researcher

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

John Willauer
I am using Ubuntu Linux version 12.04 with:

     mspdebug     0.18-1
     db-msp430  7.2~mspgcc-7.2.2
     gcc-msp439  4.5.3~mspgcc-201

The MSP430 development software was downloaded from:

     http://extras.ubuntu.com/ubuntu precise main #Third party
developers repository

I have developed several applications for the msp430g2553 but always got
a Segment fault when I tried to use gdb.

--
John
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -



On 06/22/2013 05:12 PM, Eric Decker wrote:

>
> What version of msp430-gdb are you running? Where did you get it?
>
> do..
>
> dpkg -l "*msp430*"
>
> and how do you have apt configured?    What repository are you using
> to get the tools from?
>
>
>
> On Sat, Jun 22, 2013 at 5:10 PM, John Willauer <[hidden email]
> <mailto:[hidden email]>> wrote:
>
>     How do I eliminate the "Segmentation fault" that occurs when I
>     start msp430-gdb  using the following procedure Jose Luis Honorato
>     described in his response to Ravim.
>
>     When the msp430-gdb is started, in the second shell, a
>     Segmentation fault is reported then the msp430-gdb terminates.
>
>     I am trying to use  gdb  to debug code running on a Launchpad with
>     a msp430g2553 chip.
>
>
>     --
>     John
>     - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
>
>     On 06/22/2013 01:06 PM, Eric Decker wrote:
>>
>>     Just asking how to get rid of a "seg fault" isn't to helpful.
>>
>>     What program was actually running?   What version?  What address?
>>
>>
>>     On Sat, Jun 22, 2013 at 11:55 AM, John Willauer
>>     <[hidden email] <mailto:[hidden email]>> wrote:
>>
>>         How do I eliminate the "Segmentation fault" I get when I try
>>         it using:
>>
>>            Ubuntu          12.04
>>            mspdebug     0.18-1
>>            gdb-msp430  7.2~mspgcc-7.2.2
>>            gcc-msp439  4.5.3~mspgcc-201
>>
>>         --
>>         John
>>         - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>>
>>
>>
>>         On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:
>>
>>             Hi Ravim,
>>
>>             I can't see the output messages you intended to include,
>>             but here's a short
>>             how-to. I just hope you don't have a specific problem
>>             with your setup.
>>
>>             You can use the ez430-FET emulator to program the
>>             msp-exp430f5529 without
>>             any external hardware. Just plug your mini USB cable to
>>             the lower left USB
>>             connector (the one in the ez430-FET emulator) and run:
>>
>>             sudo mspdebug rf2500 "prog bin.elf"
>>
>>             That should program the device after a few console messages.
>>
>>             You can use mspdebug with gdb too, for that you should:
>>
>>                 1. Run mspdebug (sudo mspdebug rf2500)
>>                 2. In mspdebug, type gdb
>>                 3. In another window, run msp430-gdb
>>                 4. In gdb, type target remote localhost:2000
>>                 5. Done
>>
>>             This is assuming you have all these tools installed, if
>>             not there are
>>             plenty of guides out there on how to install them.
>>
>>             Kind regards,
>>             Jose
>>             _______________________________________________
>>             Mspgcc-users mailing list
>>             [hidden email]
>>             <mailto:[hidden email]>
>>             https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>
>>
>>         ------------------------------------------------------------------------------
>>         This SF.net email is sponsored by Windows:
>>
>>         Build for Windows Store.
>>
>>         http://p.sf.net/sfu/windows-dev2dev
>>         _______________________________________________
>>         Mspgcc-users mailing list
>>         [hidden email]
>>         <mailto:[hidden email]>
>>         https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>
>>     --
>>     Eric B. Decker
>>     Senior (over 50 :-) Researcher
>>
>
>
>
>
> --
> Eric B. Decker
> Senior (over 50 :-) Researcher
>

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users
Reply | Threaded
Open this post in threaded view
|

Re: using in-board ez430 FET emulator

Eric Decker


From cPhone


On Jun 22, 2013, at 6:00 PM, John Willauer <[hidden email]> wrote:

> I am using Ubuntu Linux version 12.04 with:

old stuff.    I don't know why.     I don't support that stuff

some notes....

first until the Ubuntu repository gets sorted out use mine.  

http://tinyprod.net/repos/debian/

follow the README instructions

more below

>
>     mspdebug     0.18-1

old.  I'm using 0.21


I do t know what the state of the rest of what you got is

>     db-msp430  7.2~mspgcc-7.2.2
>     gcc-msp439  4.5.3~mspgcc-201

4.5.3 has known problems

you should be using 4.6.3

>
> The MSP430 development software was downloaded from:
>
>     http://extras.ubuntu.com/ubuntu precise main #Third party developers repository
>
> I have developed several applications for the msp430g2553 but always got a Segment fault when I tried to use gdb.
>
> --
> John
> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>
>
> On 06/22/2013 05:12 PM, Eric Decker       wrote:
>>
>> What version of msp430-gdb are you running?   Where did you get it?
>>
>> do..
>>
>> dpkg -l "*msp430*"
>>
>> and how do you have apt configured?    What repository are you using to get the tools from?
>>
>>
>>
>> On Sat, Jun 22, 2013 at 5:10 PM, John Willauer <[hidden email]> wrote:
>>> How do I eliminate the "Segmentation fault" that occurs when I start  msp430-gdb  using the following procedure Jose Luis Honorato described in his response to Ravim.
>>>
>>> When the msp430-gdb is started, in the second shell, a Segmentation fault is reported then the msp430-gdb terminates.
>>>
>>> I am trying to use  gdb  to debug code running on a Launchpad with a msp430g2553 chip.
>>>
>>>
>>> --
>>> John
>>> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>>>
>>> On 06/22/2013 01:06 PM, Eric Decker wrote:
>>>>
>>>> Just asking how to get rid of a "seg fault" isn't to helpful.
>>>>
>>>> What program was actually running?   What version?  What address?
>>>>
>>>>
>>>> On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[hidden email]> wrote:
>>>>> How do I eliminate the "Segmentation fault" I get when I try it using:
>>>>>
>>>>>    Ubuntu          12.04
>>>>>    mspdebug     0.18-1
>>>>>    gdb-msp430  7.2~mspgcc-7.2.2
>>>>>    gcc-msp439  4.5.3~mspgcc-201
>>>>>
>>>>> --
>>>>> John
>>>>> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
>>>>>
>>>>>
>>>>>
>>>>> On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote:
>>>>>> Hi Ravim,
>>>>>>
>>>>>> I can't see the output messages you intended to include, but here's a short
>>>>>> how-to. I just hope you don't have a specific problem with your setup.
>>>>>>
>>>>>> You can use the ez430-FET emulator to program the msp-exp430f5529 without
>>>>>> any external hardware. Just plug your mini USB cable to the lower left USB
>>>>>> connector (the one in the ez430-FET emulator) and run:
>>>>>>
>>>>>> sudo mspdebug rf2500 "prog bin.elf"
>>>>>>
>>>>>> That should program the device after a few console messages.
>>>>>>
>>>>>> You can use mspdebug with gdb too, for that you should:
>>>>>>
>>>>>>     1. Run mspdebug (sudo mspdebug rf2500)
>>>>>>     2. In mspdebug, type gdb
>>>>>>     3. In another window, run msp430-gdb
>>>>>>     4. In gdb, type target remote localhost:2000
>>>>>>     5. Done
>>>>>>
>>>>>> This is assuming you have all these tools installed, if not there are
>>>>>> plenty of guides out there on how to install them.
>>>>>>
>>>>>> Kind regards,
>>>>>> Jose
>>>>>> _______________________________________________
>>>>>> Mspgcc-users mailing list
>>>>>> [hidden email]
>>>>>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>>>>
>>>>> ------------------------------------------------------------------------------
>>>>> This SF.net email is sponsored by Windows:
>>>>>
>>>>> Build for Windows Store.
>>>>>
>>>>> http://p.sf.net/sfu/windows-dev2dev
>>>>> _______________________________________________
>>>>> Mspgcc-users mailing list
>>>>> [hidden email]
>>>>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users
>>>>>
>>>> --
>>>> Eric B. Decker
>>>> Senior (over 50 :-) Researcher
>>>>
>>>
>>
>>
>>
>> --
>> Eric B. Decker
>> Senior (over 50 :-) Researcher
>>
>

------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:

Build for Windows Store.

http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Mspgcc-users mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/mspgcc-users